Kenwood TK-5410 Uživatelský manuál

© B62-2155-00 (K, K2, K3, K4, K5, K6, K7)09 08 07 06 05 04 03 02 01 00INSTRUCTION MANUALVHF P25 TRANSCEIVERTK-5210UHF P25 TRANSCEIVERTK-5310700/800MHz

viiisTun Code <Tk-5210/ Tk-5310 onlY> ... 33TRUNKING CALLS ...

1UNPACKING AND CHECKING EQUIPMENTNote: The following unpacking instructions are for use by your Kenwood dealer, an authorized Kenwood service facilit

2PREPARATIONBAttery pAck precAutionSDo not use battery packs or battery chargers not recommended by Kenwood.◆ Do not recharge the battery pack if it

3Information concerning the battery pack:The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to ru

4• Do not charge the battery near fires or under direct sunlight! If the battery’s protection circuit is damaged, the battery may charge at extreme

5• Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has pas

6 Using the Li-ion Battery Pack• Charge the battery pack before using it.• To keep the battery discharge at a minimum, remove the battery pack fro

7inStAlling/ removing the (optionAl) BAttery pAck1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the trans

8OptionalantennainStAlling the (optionAl) AntennAScrew the antenna into the connector on the top of the transceiver by holding the antenna at its base

9inStAlling the cAp over the univerSAl connector1 If you are not using an optional speaker/ microphone or headset, install the cap over the universal

Terminal DescriptionsUniversal connector It is possible to use a resin-based cover for the Universal connector.No. NameDescriptionSpecification I/O1 S

10GETTING ACQUAINTEDABC6MICMicrophoneSpeakerThere are 3 model types available:K/K4 models: Basic models.K2/K5/K7 models: Equipped with a display an

11q Power switch/ Volume control Turn clockwise to switch the transceiver ON. Rotate to adjust the volume. Turn counterclockwise fully to switch th

12!0 PTT (Push-To-Talk) switch Press and hold this switch, then speak into the microphone to call a station.!1 Side 2 key Press to activate its prog

13diSplAy (k2/k3/k5/k6/k7 modelS only)Indicator DescriptionThe number of bars indicates the strength of incoming signals. The antenna plus 3 bars rep

14Indicator DescriptionDisplays various characters depending on dealer settings.Appears when the VOX function is activated.Appears when the Talk Aroun

15PROGRAMMABLE FUNCTIONSRefer to the following tables to determine which functions are available for appropriate channels. Function descriptions star

16Programmable Function Con FM Con P25Trunk P25Individual 2Mix✓ ✓Key Delete 2Mix✓ ✓Key Lock✓ ✓ ✓Keyset 2,5Mix✓N/ALight 2✓ ✓ ✓Low Transmit Power✓ ✓ ✓Mo

17Programmable Function Con FM Con P25Trunk P25Status 1,2,7✓Mix✓System Search N/A N/A✓Tactical Group 1✓Mix N/ATalk Around✓ ✓ ✓Talkgroup 2Mix✓N/ATone✓

18BASIC OPERATIONSSwitching power on/ oFFTurn the Power switch/ Volume control clockwise to switch the transceiver ON.Turn the Power switch/ Volume co

19AdjuSting the volumeRotate the Power switch/ Volume control to adjust the volume. Clockwise increases the volume and counterclockwise decreases it.

iThank YouWe are grateful you have chosen Kenwood for your land mobile radio applications.Models Covered bY This ManualThe models listed below are cov

20trAnSmittingFor Trunking channels, refer to “Making Group Calls” and “Making Individual Calls” on the following pages.1 Select the desired zone and

21 Making Group Calls (P25) Channels programmed for Conventional P25 and Trunking P25 operation already have a Group ID assigned. For these channe

22 Making Individual Calls (P25) (K2/K3/K5/K6/K7 models only) If a key has been programmed with Individual, you can make calls to specified persons

23 Receiving Group Calls (P25) When you receive a group call on a Conventional channel and the received group ID matches the ID set up on your tran

24SCANScan is useful for monitoring signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only

25priority ScAnA Priority channel must be programmed in order for Priority Scan to function.When using a single Priority channel, the transceiver will

26ScAn progrAmming (k2/k3/k5/k6/k7 modelS only) <tk-5210/ tk-5310 only>Note: Scan programming is only available when using Conventional operat

274 Press the D> key to toggle the selected channel between Priority and Normal.• “P1”, “P2”, or “PP” appears on the display when Priority mode i

28FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION<TK-5210/ TK-5310 ONLY >FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol own

29 Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver must have its own Fleet and

iiThis device made under license under one or more of the following US Patents: 4,590,473; 4,636,791; 4,716,407; 4,972,460; 5,148,482; 5,185,796; 5,2

30 Transmitting1 Select your desired zone and channel.2 Press the key programmed as Status to enter Status mode or Selcall + Status to enter Selca

31 Reviewing Messages in the Stack Memory1 Press and hold the key programmed as Selcall, Status, or Selcall + Status for 1 second to enter Stack mo

32DTMF (DUAL TONE MULTI FREQUENCY) CALLSNote: DTMF calls can be made only in Conventional FM Operation.mAking A dtmF cAll Manual Dialing (K3/K6 mo

33AutodiAl (k2/k3/k5/k6/k7 modelS only)Autodial allows you to quickly call DTMF numbers that have been programmed onto your transceiver.1 Press the k

34TRUNKING CALLSmAking A telephone cAll Manual Dialing (K2/K3/K5/K6/K7 models only)1 Press the key programmed as Autodial.• The last called unit

35receiving A telephone cAll1 When a call is received, a ringing tone will sound and “PHONE CALL” will appear on the display.• If the vibrator funct

36EMERGENCY CALLSIf your transceiver has been programmed with the Emergency function, you can make emergency calls.Note: Only the Auxiliary (orange)

37SCRAMBLER (FM) <TK-5210/ TK-5310 ONLY>/ ENCRYPTION (P25)Note:◆ The Scrambler function can be used only in Conventional FM Operation. Additio

38Selecting the encryption key1 Press the key programmed as Scrambler/ Encryption Code (K2/K3/K5/K6/K7 models only) or press and hold the key program

39SIGNALINGNote: Signaling can be used only in Conventional FM Operation.Quiet tAlk (Qt)/ digitAl Quiet tAlk (dQt)Your dealer may have programmed QT

iiiOne or more of the following statements may be applicable:FCC WARNINGThis equipment generates or uses radio frequency energy. Changes or modificat

40optionAl SignAling <tk-5210/ tk-5310 only>Your dealer may also program several types of option signaling for your transceiver channels. 2-to

41VOICE OPERATED TRANSMISSION (VOX)VOX can be activated or deactivated by your dealer. VOX operation allows you to transmit hands-free. This feature

42voX operAtion1 Connect the headset to the transceiver.• The VOX function does not activate when a headset is not connected to the accessory termin

43CLOCK (K2/K3/K5/K6/K7 MODELS ONLY)If activated by your dealer, your transceiver can track the time with its built-in clock. The time will display m

44ADVANCED OPERATIONSYour transceiver operations vary according to the functions that your dealer has programmed onto the transceiver keys. Following

45• Channel Recall (RCL) Press this key during Scan to return to the last called zone and channel.• Channel Select Turn the selector clockwise to in

46• Home Channel (HOM) Press this key to jump to your home zone and channel (pre-programmed by your dealer). If activated by your dealer, you can s

47• Monitor (MON) Press this key to turn the transceiver signaling off, to listen to all calls that are received on the channel. Press the Monitor k

48• Scan Program (SCP) <TK-5210/ TK-5310 only> Refer to “Scan programming” on page 26.• Scrambler/ Encryption (SE) Refer to “SCRAMBLER (FM) &l

49• Squelch Off (MON) Press this key to turn the transceiver squelch off, to better hear weak signals on the channel. Press the Squelch Off key agai

ivThe RBRC Recycle seal found on Kenwood nickel-cadmium (Ni-Cd) battery packs indicates Kenwood’s voluntary participation in an industry program to co

50• Tone (TON) Press this key to toggle the transceiver audible tones ON and OFF.• Vibrator (VIB) <TK-5210/ TK-5310 only> Press and hold this

51BACKGROUND OPERATIONSYour dealer can activate a variety of transceiver functions to perform without any additional operation on your part.time-out t

52low BAttery wArningLow Battery Warning alerts you when the battery needs to be recharged.On all transceivers, your dealer can set an alert tone to s

53compAnderThe compander can be programmed only for specific Conventional FM channels. If it has been programmed by your dealer, transmitted signals

54Site trunkingOn Trunking channels, if set up by your dealer, the transceiver will indicate a network condition on the registered site. On K2/K3/K5/

55VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNITWhen using the optional VGS-1 voice guide & storage unit, you gain access to the voice recorder and

56 Playback To play back a recorded conversation, memo, or message:1 Press the key programmed as Playback to enter Playback mode.• If the last ac

vPreCauTions• Do not charge the transceiver and battery pack when they are wet.• Ensure that there are no metallic items located between the transce

viTurn the transceiver power off in the following locations:• Near explosives or blasting sites.• In aircrafts. (Any use of the transceiver must fo

viiCONTENTSUNPACKING AND CHECKING EQUIPMENT.........1suPPlied aCCessories ............